Water Distiller

Water Distillers / Distillation

 

 Stuart Aquatron water distiller

The Aquatron is fully automatic, borosilicate glass stills with silica sheathed heaters. Available with outputs of 4 or 8 litres/hr single distilled or a double unit producing 4 litres/hr of double distilled water. The Aquatron is capable of being converted to pre-treated feed to remove the need for descaling.

 Stuart Distinction water distiller

Economical borosilicate glass still with silica sheathed heater. Produces 4 litres/hr single distilled water. A safety device is included which turns off the heater and prevents overflow when the collecting reservoir is full.

 Stuart Merit water distiller

The Merit is a simple glass water still with long life metal heater and twin safety thermostats. Ideal for schools and colleges.

 

Use the search box to narrow the results of your search. RESET to clear your search.

SKU# A4000

Aquatron® water still, 4L/Hr, single distillation

  

Fully automatic operation
High purity pyrogen free output
Low temperature distillate
Operates from any raw water supply
Reservoir level control
Simple conversion to pre-treated feed
Supplied with wall mounting bracket
Safety features allow unattended operation
Simple to clean

Three models are available giving outputs of 4 litres/hour single distilled water. The high quality PYREX® borosilicate glassware coupled with silica sheathed heaters gives pyrogen free distillate of the highest purity from virtually any raw water supply.

The unique condenser design ensures that the droplets of distilled water remain in contact with the cooling coil for the longest possible time ensuring maximum energy transfer. This produces cold distilled water ready for immediate use and pre-heats the boiler feed to increase efficiency.

All glass construction allows rapid descaling using strong mineral acids. A built in "clean" function and integral acid addition funnel make the cleaning operation simple and safe with no need to dismantle any of the glassware. A large bore ROTAFLO® stopcock with PTFE key is fitted for easy draining of chemicals after cleaning. 

A flow sensing device will detect any reduction in the flow of cooling water to below the required level and will turn off the still before it can overheat. Sensing the flow of cooling water rather than its pressure is safer and allows the still to run normally on low pressure supplies down to 3psi (20kPa). As a fail-safe device there is an over-temperature thermostat mounted in the boiling chamber.

The Aquatron is very easy and safe to assemble and maintain. Both the acrylic safety screen and the cabinet lid are removable giving unrivalled access to the glassware components. Screwthreads are incorporated on all water connections so hoses can be fitted and removed easily and safely without risk of breakage. Every Aquatron® water still is supplied with a reservoir level control.

The control is a simple and effective system which can be fitted to virtually any type of reservoir vessel. It will turn the still off when the reservoir is full and restart it when the level in the reservoir drops as distilled water is removed for use making it fully automatic. water purification

A4000
Produces 4 litres/hour single distilled water. Can operate standing on the laboratory bench or be wall mounted. Supplied with easy to fit wall mounting bracket.
 
  A4000
Output, l/hr 4, single
pH 5.0 - 6.5
Conductivity, µScm-1 1.0 - 2.0
Resistivity, mOhm-cm 0.5 - 1.0
Temperature, °C 25 - 35
Pyrogen content* Pyrogen free
Water supply 1 l/min, 3-100psi, (20-700kPa)
Electrical supply 240V, 50/60Hz, single phase
Max. power, kW 3
Dimensions (wxdxh), mm 550x240x410
  

Please note water still heating elements are excluded from our 3 year warranty and are only covered for 1000hrs use

 

 


Availability: IN STOCK
SKU# A4000D

Aquatron® water still, 4L/Hr, double distillation

 

Fully automatic operation
High purity pyrogen free output
Low temperature distillate
Operates from any raw water supply
Reservoir level control
Simple conversion to pre-treated feed
Supplied with wall mounting bracket
Safety features allow unattended operation
Simple to clean

Three models are available giving outputs of 4 litres/hour double distilled water. The high quality PYREX® borosilicate glassware coupled with silica sheathed heaters gives pyrogen free distillate of the highest purity from virtually any raw water supply.

The unique condenser design ensures that the droplets of distilled water remain in contact with the cooling coil for the longest possible time ensuring maximum energy transfer. This produces cold distilled water ready for immediate use and pre-heats the boiler feed to increase efficiency.

All glass construction allows rapid descaling using strong mineral acids. A built in "clean" function and integral acid addition funnel make the cleaning operation simple and safe with no need to dismantle any of the glassware. A large bore ROTAFLO® stopcock with PTFE key is fitted for easy draining of chemicals after cleaning. 

A flow sensing device will detect any reduction in the flow of cooling water to below the required level and will turn off the still before it can overheat. Sensing the flow of cooling water rather than its pressure is safer and allows the still to run normally on low pressure supplies down to 3psi (20kPa). As a fail-safe device there is an over-temperature thermostat mounted in the boiling chamber.

The Aquatron is very easy and safe to assemble and maintain. Both the acrylic safety screen and the cabinet lid are removable giving unrivalled access to the glassware components. Screwthreads are incorporated on all water connections so hoses can be fitted and removed easily and safely without risk of breakage. Every Aquatron® water still is supplied with a reservoir level control.

The control is a simple and effective system which can be fitted to virtually any type of reservoir vessel. It will turn the still off when the reservoir is full and restart it when the level in the reservoir drops as distilled water is removed for use making it fully automatic. water purification

A4000D
Produces 4 litres/hour double distilled water for higher purity levels. The first stage distillation is carried out in a glassware set mounted at the front of the cabinet allowing easy access for descaling. The distilled water is fed to a second set of glassware mounted at the rear and distilled a second time. The rear glassware is fitted with a level sensor to ensure the heater is only activated when there is sufficient water in the boiler.


  A4000D
Output, l/hr 4, double
pH 5.0 - 6.5
Conductivity, µScm-1 1.0 - 1.5
Resistivity, mOhm-cm 0.7 - 1.0
Temperature, °C 25 - 35
Pyrogen content* Pyrogen free
Water supply 1 l/min, 3-100psi, (20-700kPa)
Electrical supply 240V, 50/60Hz, single phase
Max. power, kW 6
Dimensions (wxdxh), mm 550x410x410
  
Please note water still heating elements are excluded from our 3 year warranty and are only covered for 1000hrs use

 


Availability: IN STOCK
SKU# A8000

Aquatron® water still, 8L/Hr, single distillation

 

Fully automatic operation
High purity pyrogen free output
Low temperature distillate
Operates from any raw water supply
Reservoir level control
Simple conversion to pre-treated feed
Supplied with wall mounting bracket
Safety features allow unattended operation
Simple to clean

Three models are available giving outputs of 8 litres/hour single distilled water. The high quality PYREX® borosilicate glassware coupled with silica sheathed heaters gives pyrogen free distillate of the highest purity from virtually any raw water supply.

The unique condenser design ensures that the droplets of distilled water remain in contact with the cooling coil for the longest possible time ensuring maximum energy transfer. This produces cold distilled water ready for immediate use and pre-heats the boiler feed to increase efficiency.

All glass construction allows rapid descaling using strong mineral acids. A built in "clean" function and integral acid addition funnel make the cleaning operation simple and safe with no need to dismantle any of the glassware. A large bore ROTAFLO® stopcock with PTFE key is fitted for easy draining of chemicals after cleaning. 

A flow sensing device will detect any reduction in the flow of cooling water to below the required level and will turn off the still before it can overheat. Sensing the flow of cooling water rather than its pressure is safer and allows the still to run normally on low pressure supplies down to 3psi (20kPa). As a fail-safe device there is an over-temperature thermostat mounted in the boiling chamber.

The Aquatron is very easy and safe to assemble and maintain. Both the acrylic safety screen and the cabinet lid are removable giving unrivalled access to the glassware components. Screwthreads are incorporated on all water connections so hoses can be fitted and removed easily and safely without risk of breakage. Every Aquatron® water still is supplied with a reservoir level control.

The control is a simple and effective system which can be fitted to virtually any type of reservoir vessel. It will turn the still off when the reservoir is full and restart it when the level in the reservoir drops as distilled water is removed for use making it fully automatic. water purification

A8000
Produces 8 litres/hour single distilled water, ideal for the larger laboratory. Glassware is enclosed in the same cabinet as the A4000 so can operate standing on the laboratory bench or be wall mounted. Supplied with easy to fit wall mounting bracket.


  A8000
Output, l/hr 8, single
pH 5.0 - 6.5
Conductivity, µScm-1 1.0 - 2.0
Resistivity, mOhm-cm 0.5 - 1.0
Temperature, °C 25 - 35
Pyrogen content* Pyrogen free
Water supply 1 l/min, 3-100psi, (20-700kPa)
Electrical supply 240V, 50/60Hz, single phase
Max. power, kW 6
Dimensions (wxdxh), mm 550x240x410
 

Please note water still heating elements are excluded from our 3 year warranty and are only covered for 1000hrs use

 

 


Availability: IN STOCK
SKU# D4000

Distinction water still, 240V, single distillation, 4l/h


All glass construction
Two independent safety thermostats
Safety reservoir full shut off
Wall mountable
Silica sheathed heaters

All glass construction with silica sheathed heaters ensures top purity distillate at an economical price. Fitted with a control device to turn off the heater when the collecting reservoir is full. Prevents overflow if the still is inadvertently left switched on when unattended. With two independent safety thermostats to prevent over heating in the event of an interruption to the water supply.

The unique condenser design ensures that the droplets of distilled water remain in contact with the cooling coil for the longest possible time producing cold distilled water and pre-heating the boiler feed to increase efficiency.

Screwthreads are incorporated on all water connections so hoses can be fitted and removed easily and safely without risk of breakage. Built in acid addition funnel and drain stopcock allow easy de-scaling without dismantling the glassware. The stand is pre-drilled to facilitate wall mounting.


Output 4 litres/hr, single distilled
pH 5.0 - 6.5
Conductivity, µScm-1 1.0 - 2.0
Resistivity, mOhm-cm 0.5 - 1.0
Temperature 25 - 35°C
Pyrogen content * Pyrogen free
Water supply 1 litre/min, 3 - 100psi, (20-700kPa)
Electricity supply 240, 50/60Hz, single phase
Power requirement 3kW
Dimensions (w x d x h) 540 x 160 x 410mm

 

 
Please note water still heating elements are excluded from our 3 year warranty and are only covered for 1000hrs use
 

 

 

 

 


Availability: IN STOCK
SKU# W4000

Merit water still, single distillation, 4l/h

 

Economical price
Glass construction with long life metal heating element
Two independent safety thermostats
Wall mountable

The Merit is the ideal choice for budget conscious laboratories that can't afford to compromise on quality. It combines economy and high performance with a host of other features which comparable stills cannot match. 

Built in acid addition funnel and drain stopcock allow easy descaling without dismantling the glassware. The unique condenser design ensures that the droplets of distilled water remain in contact with the cooling coil for the longest possible time producing cold distilled water and pre-heating the boiler feed to increase efficiency. Screwthreads are incorporated on all water connections so hoses can be fitted and removed easily and safely without risk of breakage.

Safety features include two independent safety thermostats to prevent over heating in the event of failure of the water supply. The stand is pre-drilled to facilitate wall mounting.

 


Output 4 litres/hr, single distilled
pH 5.0 - 6.5
Conductivity, µScm-1 3.0 - 4.0
Resistivity, mOhm-cm 0.25 - 0.3
Temperature 25 - 35°C
Pyrogen content * Pyrogen free
Water supply 1 litre/min, 3 - 100psi, (20-700kPa)
Electricity supply 240V, 50/60Hz, single phase
Power requirement 3kW
Dimensions, (w x d x h) 500 x 150 x 450mm

  

 

Please note water still heating elements are excluded from our 3 year warranty and are only covered for 1000hrs use
 

 


Availability: IN STOCK