Controllers ( Temperature )

Temperature Controllers and Thermoregulators

 

 Techne Thermoregulators

Techne ® invented the "Clip On" thermoregulator in 1948 and now offer four units. Thermoregulators are designed to be used with the Techne ® unheated water baths or any other suitable laboratory vessels. They will heat, circulate and safely control the temperature of the liquid in the bath within precise limits.

 

 

***Techne Baths HERE

 

 Electrothermal Temperature Controllers

The Electrothermal Controllers line includes a range of models for single, double and triple place and percentage off/on. Controller line includes the ideal controller to pair with your heating mantles, mats and tapes. Either digital or analogue.

 Electrothermal MC5, MC242, MC227, MC228X1 Analogue Controller

Electrothermal offer 3 different models of 1-Way Heating Controllers which operate up to 800W (MC5), 1800W (MC242) or 2300W (MC227); MC228X1 is the 115V version of MC227 and operates up to a maximum of 1100W. These heating controllers can control one piece of laboratory equipment at a time, or an equivalent load, i.e. for a CMUV22/L which has 3 elements, an MC5 would be needed on each element. For all 1-Way Heating Controllers The MC5, MC242, MC227 and MC228X1 Heating Controllers have been designed to control the heating of resistive loads for bench top operation. The heating controllers deliver different levels of power according to your requirements and are suitable for EM series Electromantles, the Electric Bunsen and Heating Tapes.
 

 Electrothermal MC810B Digital Heating Controller

can be used in 3 ways:
• In On/Off mode with the hysteresis loop controlling power switching
• As a PID (Proportional, Integrated, Derivative) controller
• As a temperature measuring device up to 800°C, depending upon the probe accessory used.

Features
• PTFE-covered platinum resistance thermometer is included for measurements up to 250°C
• Zinc die-cast outer case is suitable for the bench or can be mounted on a 12.7cm support rod
• Programming is done by up/down controls
• Three-digit LED display allows you to set a 1°C resolution over a range of -10°C to 800°C
• A hysteresis range can be set to govern the range of temperature variation in the medium being controlled

 

 Use the search box to narrow the results of your search. RESET to clear your search.

 

SKU# FM110

Flow Monitor, 0.5 - 15 litres/minute flow rate, 230V, UK & EU Plugs

The new FM110 Flow Monitor has been carefully designed to provide increased safety in the laboratory by monitoring aqueous liquids used in heating and cooling applications and process control. 

 

The turbine assembly is comprised of components made from chemically resistant materials such as PVDF, sapphire, ceramic and viton.

A rod support clamp is provided at the rear of the controller to take a standard 12.5mm (½") diameter rod.

Technical Specifications

Flow rate

0.5 - 15 litres/minute

Mains voltage supply

115V and 230V, 50/ 60 Hz

Maximum load current

15 Amp for 115V

Maximum load current

10 Amp for 230V

Rod clamp size

12.7mm diameter

Operating ambient temperature

5°C to 40°C

Fluid temperature parameters

-30°C to 80°C

Dimensions (d x w x h), mm

100 x 120 x 80


Availability: IN STOCK
SKU# FM1102B

Flow Monitor, 0.1 - 5 litres/minute flow rate, 230V, 50-60Hz, used in conjunction with Electrothermal Multi (Extraction) Mantles EME and EMEA series

The new FM110 Flow Monitor has been carefully designed to provide increased safety in the laboratory by monitoring aqueous liquids used in heating and cooling applications and process control. 

The turbine assembly is comprised of components made from chemically resistant materials such as PVDF, sapphire, ceramic and viton. 

A rod support clamp is provided at the rear of the controller to take a standard 12.5mm (½") diameter rod.

Technical Specifications 

Flow rate

0.1 - 5 litres/minute

Mains voltage supply

115V and 230V, 50/ 60 Hz

Maximum load current

15 Amp for 115V

Maximum load current

10 Amp for 230V

Rod clamp size

12.7mm diameter

Operating ambient temperature

5°C to 40°C

Fluid temperature parameters

-30°C to 80°C

Dimensions (d x w x h), mm

100 x 120 x 80


Availability: IN STOCK
SKU# MC240

2-Way Controller, Double place percentage On/Off, 230V, 50/60Hz, 800W

  • 2-Way Controller

The MC240 Controller is a 2-channel device which provides the user with the option to control two pieces of laboratory equipment running simultaneously, but independently of each other. It operates up to a maximum of 800W per circuit, at either 115V or 230V.

The MC240 2-Way Controller has been designed to work with:

  • EM series Electromantles
  • CMU series Electromantles
  • Electric Bunsen
  • Heating Cords and Tapes

The MC240 Controller has 3 neon indictors:

  • "Power On" green neon light
  • "Mantle/Bunsen Heater On" amber neon light for channel 1
  • "Mantle/Bunsen Heater On" amber neon light for channel 2

In addition, for both channels there is a mains output, control knob and protection fuses. Both regulator control knobs can be turned clockwise to increase power. As each knob is turned, the controller's amber neon light will pulsate to show that power is being supplied to the equipment being controlled for that channel, e.g. mantles, heating tape or cord. The pulse frequency will decrease as the regulator control knob setting is increased, and at maximum setting, the amber neon will be continually illuminated.

The MC240 Controller has a short mains lead with an IEC socket to connect it to the resistive load. An accessory extension mains lead is available where remote operation is required, e.g. in a fume extraction unit.

Key Features

  • Able to control 2 pieces of laboratory equipment simultaneously
  • 3 neon indicators
  • Operates up to a maximum of 800W per circuit at either 115V or 230V

Technical Specification 

Controller power consumption     < 1W per channel

Electrical requirements: 230V      230V, 50/ 60Hz, 800W

Electrical requirements: 115V      115V, 50/ 60Hz, 800W

Dimensions (d x w x h), mm        100 x 200 x 98

Weight, kg                                1.1

 


Availability: IN STOCK
SKU# MC242

1-Way Controller, 230V, 50/60Hz, 1800W, UK & EU Plugs

  • 1-Way Controller 

The MC5, MC242, MC227 and MC228X1 Controllers have been designed to control the heating of resistive loads for bench top operation. They deliver different levels of power according to your requirements and are suitable for EM series Electromantles, the Electric Bunsen and Heating Cords and Tapes.  

Each controller has 2 neon indicators: "Power On" white neon light and "Mantle/Bunsen Heater On" amber neon light. They all have a regulator control knob which can be turned clockwise to increase power. As the knob is turned, the controller's amber neon light will pulsate to show that power is being supplied to the equipment being controlled, e.g. mantles, heating tape or cord. The pulse frequency will decrease as the regulator control knob setting is increased, and at maximum setting, the amber neon will be continually illuminated. 

A rod support clamp is provided at the rear of each controller to take a standard 12.5mm (½") diameter rod. They have a short mains lead with an IEC socket to connect them to the resistive load. An accessory extension mains lead is available where remote operation is required, e.g. in a fume extraction unit.

Technical Specification

Mains supply voltage

230V AC 50/ 60 Hz

Maximum coupled power consumption

230V  1150  Watts.

Controller power consumption

< 1 Watt

 

 

 

 

Warranty: One year parts and labour

Certification: CE 


Availability: IN STOCK
SKU# MC5

1-Way Controller, 230V, 50/60 Hz, 800W, UK & EU Plugs

  • 1-Way Controller 

The MC5, MC242, MC227 and MC228X1 Controllers have been designed to control the heating of resistive loads for bench top operation. They deliver different levels of power according to your requirements and are suitable for EM series Electromantles, the Electric Bunsen and Heating Cords and Tapes.  

Each controller has 2 neon indicators: "Power On" white neon light and "Mantle/Bunsen Heater On" amber neon light. They all have a regulator control knob which can be turned clockwise to increase power. As the knob is turned, the controller's amber neon light will pulsate to show that power is being supplied to the equipment being controlled, e.g. mantles, heating tape or cord. The pulse frequency will decrease as the regulator control knob setting is increased, and at maximum setting, the amber neon will be continually illuminated.

A rod support clamp is provided at the rear of each controller to take a standard 12.5mm (½") diameter rod. They have a short mains lead with an IEC socket to connect them to the resistive load. An accessory extension mains lead is available where remote operation is required, e.g. in a fume extraction unit. 

Technical Specification 

Mains supply voltage

230V AC 50/ 60 Hz

Maximum coupled power consumption

230V 800 Watts.

Controller power consumption

< 1 Watt

 

 

 


Warranty: One year parts and labour 

Certification: CE 


Availability: IN STOCK
SKU# MC810B

Temperature Controller, digital, 1500W, 230V, UK & EU Plugs

  • PTFE-covered platinum resistance thermometer is included for measurements to 270°C
  • Zinc die-cast outer case is suitable for the bench or can be mounted on a 12.7cm support rod
  • Programming is done by up/down controls
  • Three-digit LED display allows you to set a 1°C resolution over a range of -10°C to 800°C
  • A hysteresis range can be set to govern the range of temperature variation in the medium being controlled  

The MC810B Digital Controller provides a convenient means of temperature control, using microprocessor techniques to give ease of operation and good accuracy. 

It can be used in 3 ways:

  • In On/Off mode with the hysteresis loop controlling power switching
  • As a PID (Proportional, Integrated, Derivative) controller
  • As a temperature measuring device up to 270°C or more, depending upon the probe accessory used.

The MC810B Digital Controller may be used in conjunction with a suitable heating or cooling device, e.g. Electromantle or Electric Bunsen. For clear operation, the MC810B Digital Controller has an On/Off power switch, "Power On" amber neon indicator and an Exit/Standby button.

Programming is done via the Up/Down controls on the front panel and the 3 digit LED display allows you to set a 1°C resolution over a range of -10°C to 800°C. Temperature sensing is performed by a plug-in PTFE covered platinum resistance thermometer probe which is suitable for measurements up to 270°C. There is a 5 pin DIN socket for the temperature probe. The sample temperature is displayed on the 3-digit LED display.  

The MC810B Digital Controller has a zinc die-cast outer case and is suitable for bench and retort stand mounting or wall mounting, using the wall bracket and retort rod clamps provided. It has a short mains output lead with an IEC socket to connect it to the resistive load. An accessory mains lead is available where remote operation is required, e.g. in a fume extraction unit.

Electrical requirements: 230V

230V, 50/ 60 Hz, 1500W

Electrical requirements: 115V

115V, 50/ 60 Hz, 750 W

Controller power consumption

< 2W

Dimensions, ( d x w x h), mm

100 x 120 x 80

Weight, kg

1.1

Warranty: One year parts and labour

Certification: CE


Availability: IN STOCK
SKU# FTE10ADC

Thermoregulator, analogue, -20°C to 95°C

Techne ® invented the "Clip On" thermoregulator in 1948 and now offer four units. Thermoregulators are designed to be used with the Techne ® unheated water baths or any other suitable laboratory vessels. They will heat, circulate and safely control the temperature of the liquid in the bath within precise limits. 

  • Temperature range of -20°C* to 95°C
  • Excellent temperature stability: ±0.01°C at 40°C
  • Simple to use analogue control
  • Suitable for most routine laboratory applications
  • User adjustable over-temperature cut-out for unbeatable safety

Technical Specification

Specifications to DIN 12876

TE-10A

Temperature range*

-20°C to +95°C

Temperature selec tion

Analogue

Temperature stability using water @ 40°C

±0.01°C

Method of control

Proportional

Temperature sensor

Thermistor

Adjustable over-temperature cut-out

Yes

Low liquid level cut-out

Yes

Pump capacity litres/minute

10

Pump capacity (mbar)

145

Nominal heater power at 120V (W)

1000

Nominal heater power at 240V (W)

1000

Extension below base (mm)

145

Dimensions L x W x H (mm)

237 x 124 x 260

Shipping weight

3.7kg

 * Refrigeration or cooling coil required for below ambient cooling (see Techne Flow and Dip Coolers)


Availability: IN STOCK
SKU# FTE10DDC

Thermoregulator, digital, -40°C to 120°C

Techne ® invented the "Clip On" thermoregulator in 1948, and now offer four units. Thermoregulators are designed to be used with the Techne ® unheated water baths or any other suitable laboratory vessels. They will heat, circulate and safely control the temperature of the liquid in the bath within precise limits.

  • Temperature range of -40°C* to 120°C
  • Excellent temperature stability: ±0.01°C at 40°C
  • 4 digit setting with a bright LED digital temperature display
  • Suitable for most routine laboratory applications
  • User adjustable over-temperature cut-out
  • Low liquid level cut-out as standard

Technical Specification

Specifications to DIN 12876

TE-10D

Temperature range*

–40°C to +120°C

Temperature selec tion

Digital

Temperature stability using water @ 40°C

±0.01°C

Method of control

PID

Temperature sensor

PRT

Adjustable over-temperature cut-out

Yes

Low liquid level cut-out

Yes

Pump capacity litres/minute

10

Pump capacity (mbar)

145

Nominal heater power at 120V (W)

1000

Nominal heater power at 240V (W)

1000

Extension below base (mm)

145

Dimensions L x W x H (mm)

237 x 124 x 260

Shipping weight

3.9kg

 * Refrigeration or cooling coil required for below ambient cooling (see Techne Flow and Dip Coolers)


Availability: IN STOCK
SKU# FTU20DDC

Thermoregulator, digital, -40°C to 200°C, 1.8 kW

Techne ® invented the "Clip On" thermoregulator in 1948, and now offer four units. Thermoregulators are designed to be used with the Techne ® unheated water baths or any other suitable laboratory vessels. They will heat, circulate and safely control the temperature of the liquid in the bath within precise limits.

  • A wider temperature range of –40°C* to 200°C
  • Excellent temperature stability: ±0.005°C at 40°C
  • 1.8kW heater power for fast heat up
  • 4 digit setting with a bright LED digital temperature display
  • This unit incorporates an RS232 connection
  • User adjustable over-temperature cut-out
  • Low liquid level cut-out as standard

Technical Specification 

Specifications to DIN 12876

TU-20D

Temperature range*

–40°C to +200°C

Temperature selec tion

Digital

Temperature stability using water @ 40°C

±0.005°C

Method of control

PID

Temperature sensor

PRT

Adjustable over-temperature cut-out

Yes

Low liquid level cut-out

Yes

PC Interface

Yes RS232

Pump capacity litres/minute

10

Pump capacity (mbar)

145

Nominal heater power at 120V (W)

1500

Nominal heater power at 240V (W)

1800

Cooling coil

No

Extension below base (mm)

145

Dimensions L x W x H (mm)

237 x 124 x 260

Shipping weight

4.0kg

 * Refrigeration or cooling coil required for below ambient cooling (see Techne Flow and Dip Coolers) 


Availability: IN STOCK
SKU# FTU20HDC

Thermoregulator, digital, -40°C to 250°C, 1.8 kW

Techne ® invented the "Clip On" thermoregulator in 1948, and now offer four units. Thermoregulators are designed to be used with the Techne ® unheated water baths or any other suitable laboratory vessels. They will heat, circulate and safely control the temperature of the liquid in the bath within precise limits.

  • This sophisticated Tempunit ® covers a wide temperature range of -40°C* to 250°C
  • Excellent temperature stability: ±0.005°C at 40°C
  • 1.8kW heater power for fast heat up
  • 4 digit setting with a bright LED digital temperature display
  • RS232 connection supplied with TechneWorks software package and connecting lead as standard
  • User adjustable over-temperature cut-out with an audible alarm fitted
  • Low liquid level cut-out as standard

 Technical Specification

Specifications to DIN 12876

TU-20HT

Temperature range*

–40°C to +250°C

Temperature selec tion

Digital

Temperature stability using water @ 40°C

±0.005°C

Method of control

PID

Temperature sensor

PRT

Adjustable over-temperature cut-out

Yes

Low liquid level cut-out

Yes

PC Interface

Yes RS232

Pump capacity litres/minute

Internal circulation only

Pump capacity (mbar)

-

Nominal heater power at 120V (W)

1500

Nominal heater power at 240V (W)

1800

Cooling coil

Option

Extension below base (mm)

145

Dimensions L x W x H (mm)

237 x 124 x 260

Shipping weight

4.0kg

* Refrigeration or cooling coil required for below ambient cooling (see Techne Flow and Dip Coolers)


Availability: IN STOCK